Spraying puts the coating down as an even film with no brush marks, no roller texture and no ridges in the profile. It is what separates cabinet painting that looks factory-made from a kitchen that looks hand-coated at arm's length.
The split is simple. Doors, drawer fronts and loose shelving all travel out to a filtered booth, while carcasses, face frames and end panels are sprayed inside the house behind sealed containment. Kitchens in the tight post-war houses off Ritson Road and the open-plan builds up near Conlin Road are handled the same way.
Why Off-Site Spraying Produces A Better Door
A door sprayed flat cannot sag, which is the first advantage of off-site cabinet painting. Laid horizontally in a clean, temperature-controlled booth, the coating levels under its own weight and dries without dust, insects or a draft from an open patio door. That is not achievable on a rack in a kitchen.
Dust is the other half of it. A booth filters the air going in and pulls overspray out, so the cabinet painting film stays smooth instead of picking up grit that then has to be sanded back. Doors are stacked flat to harden before they travel, which is why the turnaround is measured in days rather than hours.
On-Site Cabinet Painting Behind Sealed Containment
Boxes cannot leave the house, so the cabinet painting containment comes to them. Plastic sheeting runs floor to ceiling, appliances and counters are covered, floors are papered, and an extraction fan pulls air out of the work zone. Adjacent rooms stay clean and the house stays livable.
The frames then get the same primer, the same topcoat and the same coat count as the doors. Matching the two is the point of doing cabinet painting this way. Boxes usually take two or three days, which is the whole of the on-site portion for an average kitchen.
Thin Coats Beat Thick Ones Every Time
Two thin cabinet painting coats outlast one heavy one. A thick film skins over, traps solvent underneath, stays soft in the middle for weeks and chips in sheets when a pot handle catches it. Thin sprayed passes flash off properly and build a hard, dense layer.
Between coats the surface gets a light sand, usually around 320 grit, to knock down any nib and give the next pass a key. Three coats is typical, and a deep navy or charcoal often needs a fourth. This is slow, unglamorous work and it is most of what good cabinet painting consists of.
Waterborne Enamels And Two-Component Polyurethanes
Two product families cover almost every cabinet painting job. Waterborne alkyd enamels lay down well from a gun, carry low VOC levels, come in thousands of colours and reach full hardness over about a month. Two-component polyurethanes, mixed with a hardener before spraying, are sandable in a couple of hours and fully cured inside a day.
The choice follows the kitchen. A busy family kitchen or a rental goes to the harder system, while a quieter house may be well served by an enamel in satin. Either way the product is named on the quote before the cabinet painting starts. Sprayed work on oak and on melamine and laminate uses the same method with a different primer underneath.
Ask About Sprayed Cabinet Painting For Your Kitchen
Spraying is the default here rather than an upgrade, and the quote says so in writing. Call +1 (289) 201-5963 or send a door count through the contact form to get a price. The home page lists the other cabinet painting work done across the city, Courtice and Bowmanville.
Cabinet Spray Painting Questions
Why are the doors sprayed off site?
A door sprayed flat cannot sag. In a clean, filtered booth the coating levels under its own weight and dries without dust or drafts, which a rack in a kitchen cannot match. Doors are stacked flat to harden before they travel back, so turnaround is measured in days.
How many coats does a sprayed kitchen get?
Three coats is typical, with a light sand around 320 grit between them. A deep navy or charcoal often needs a fourth. Two thin coats outlast one heavy coat, because a thick film stays soft in the middle for weeks and chips in sheets when a pot handle catches it.
Which products are sprayed?
Two families cover almost every job. Waterborne alkyd enamels carry low VOC levels and reach full hardness over about a month. Two-component polyurethanes are mixed with a hardener, sandable in a couple of hours and hard within a day. The product is named on the quote before work starts.